AD725ARZ monochrome output
Hello all, Please let me know your advice about below when input signal to AD725ARZ is monochrome analog signal. 1: Is there any problem with input to7pin GIN ? 2: Is there any problem with connecting...
View ArticleQuery about ADL5545 and ADL5521' Gerber Files
Hi there, I download gerber files of ADL5545 and ADL5521 from ADI official website, which also are attached for your quick check. But have problem opening it. Appreciate if you could let me know which...
View ArticleADV7513 and bt.565 (PAL)
I use ADV7513.Input – bt.565: 8bit on ADV7513:D[15..8], embedded sync, 576i@50 (PAL). Settings for formatting of Video Input must be (“ADV7513_Programming_Guide.pdf”):ID=4 // YCbCr 4:2:2, 2X...
View ArticleAppropriate Receiver Termintion
Hello, I am in the process of trying to produce a point to point communication with two Xilinx Virtex 7 VC707 FPGAS, each connected with an AD-FMCOMMS1-EBZ FMC. In order to do this, I know that one FMC...
View ArticleAD7324 c code
Hi, Is there any c code for ad7324 or ad 732X family (12 bit adc ) available that I can download ? Thank you
View ArticleEVAL-INAMP-82RM eval board for pressure sensor
Hi, I have a Honeywell flow thru pressure sensor (bridge configuration), and I was hoping for a "quick and dirty" solution to measuring the output. THe output changes at 1mV per 1psi change in...
View ArticleUsing EVAL-ADXRS624Z
Hello, I'm having difficulty using the evaluation board for gyroscope ADXRS624. I am applying +5V to pins 1 and 13, with ground on pins 8 and 12. I am reading pin 2 as the output. Instead of receiving...
View ArticleOn Chip Termination
According to the AD9361 Register Map, there is a bit setting "Rx On Chip Term" in D4 at register address 03C.How is this bit used with LVDS mode?
View ArticleAbout state of I2C pin of ADV7390 during power up and reset state.
Dear support team, What is output of I2C pin of ADV7390 during Power up and Reset low?Low output or Hi-Z ? Best regards,Takepiro
View ArticleClik here to view.
ADIS16485 driver for Windows
I had to convert all of my codes and software from Linux to Windows . Is there any SDK for windows? How I can read its USB port? Thank you,Siavash.
View ArticleAudio sample playback in sigmaDSPs?
Hello guyz, I just wanted to ask, whether a playback of a pre-loaded in memory short audio samples (several mSeconds) is, or will be planned for implementation?I believe a long while ago I asked that...
View ArticleClik here to view.
ADP2503 operation. is it typo? (fig22,23)
HiI would like to make sure the datasheet's description.Regarding Figure 22 and 23, SW1 and SW2 waveform might be opposite, I think.Page 11 of RevC says in buck mode PMOS2 is always active NMOS2 is...
View ArticleUsing Picaxe 20x2 SPI to set ADF4106
Hi, I have a need to build a 3910 MHz PLL. I decided to use a Mini circuit integrated PLL/VCO part number KSN-3940. It's a great device and the base PLL uses the ADF4106. As I need to set the frequency...
View ArticleMigrating from ADG1606 to ADG726
Dear EngineerZone Experts-Thanks in advance for your help. My team is currently using two analog multiplexer ADG1606 chips to control 31 signal channels. The PCB power is +/-5v. Due to some new design...
View Articlelooking for declaration of XPAR_AXI_ADC_1C_0_BASEADDR ??
Trying to implement the reference design of the AD9467-FMC evaluation board connected to the ZED-board I am stopped by a missing base address parameter.In file cf_ad9467.h I added for connecting other...
View ArticleSAFP Help
Hi All, Looking for a little bit of help with scripting for the stand alone flash programmer. I have cobbled together a starter script to use the SAFP instead of VisualDSP++5.0. I have gotten through...
View ArticleADV7393 - NTSC Output
I am having issues regarding the ADV7393 Eval Board:I could generate CVBS output of the SD test patterns (color bar) for NTSC and PAL successfully following the instruction of “Internal test pattern...
View ArticleEVAL-ADF4350-EB2Z update rate
Using libusb-1.0.9 and cyusb_linux_1.0.4, I've written software that is controlling the RF output frequency of a EVAL-ADF4350-EB2Z Rev B evaluation board. It works fine as long as I wait at least 50...
View ArticleDROVR Output on AD9914
Hi, I'm currently controlling an AD9914 eval board with an Arduino using SPI. I'm using the 9914's ramp generator to make chirps, and would like to use the DROVER-BUF to trigger a digitizer. Using the...
View Article"BEMICRO FPGA PROJECT FOR AD7656-1 WITH NIOS DRIVER" ,the AD7656-1 IP
In the ip core of AD7656-1 for NIOS, the converting start signal is defined as adc_convst_o. Its width is only 1 bit, but actually the AD7656-1 has 3 converting control pin CONV_A,CONV_B&CONV_C,...
View Article