AD7608 serial read trouble
I'm reading all 8 channels in 144 SCLK cycles. Both SCLK and CS generated by a CPLD from a common 25MHz clock, SCLK running continuously at 12.5MHz, CS synchronous with SCLK rising edges, data bits...
View Article[ADV7282-M] Could you tell me the difference between CCAPD_Q and VDP_CCAPD_Q?
Hello.I have a question about ADV7282-M. Could you tell me the difference between two following registers?0x46 bit0 CCAPD_Q0x4E bit0 VDP_CCAPD_Q I think these registers seem to have a same...
View ArticleClik here to view.
EQ Low- and High-Shelf filter coefficients comming back - Mysterious S factor.
Hi everybodyI have to calculate EQ coefficients before start my ADAU1701 every time. The first filter in EQ is LowShelf filter and last one - High-Shelf. Rest are peaking filters. There are some...
View ArticleClik here to view.
ADXL375 - Data interpretation
Hello, I need some help by interpreting my data from the ADXL375. The register 0x31 is set to 00001011. For the lsb of each axis i receive values from 0 to 254 in steps of 2.For the msb of x and y axis...
View ArticleHelp with split power operation of AD7176-2 EVAL board
Good morning, I wish to configure the EVAL board with a split 2.5V power supply. As I delved into the configuration option deeper some questions arose that I would like answered/points I would like...
View ArticleBlackfin A-V Extender
Hi,I am just looking for same pice of hardware suitable to connect camera sensor to BF548 EZ-Kit.I am found your A-V Extender and got few questions.First of all, do we have a camera modul included in...
View ArticleAbout S-parameter
If you have S-parameter of following parts, please provide me with it.- HMC783LP6CE- HMC1041LC4- HMC899LP4E If you do not have S-parameter of the above parts, please tell me that. Best Regards, Tomo
View ArticleAD9257 ADC driver and VCM output buffer recommendations
Hello, I am using the AD4932-1 to drive the ADC inputs for an AD9253 in a current design. Is this still the recommended driver amp for my application? If so, I currently use the VCM output of the...
View ArticleADIS16485 - Problems with PROD_ID
I have an ADIS16485, which I want to interface to a development board with an ARM7 microcontroller. To facilitate the interfacing, I prepared a specific card for the IMU (shown on IMU_setup.jpeg), but...
View ArticleClarification needed on warranty for ADIS16364 sensor
Question 1: I understand that the standard warranty on these devices is 12 months. How is this time interval measured? In reviewing the invoices and packing lists from parts purchased thru...
View ArticleAD9361+Zedboard and AD9361_iiostream example
Hello to all,i have some problem on the file AD9361_iiostream.c found in the libiio example folder.i have cross-compiled and installed the libiio on the Linux Centos host,i have put this compileds file...
View Articleadv7611 sclk value for 24 bit
Hi, We want to configure adv7611 for 24 bit i2s mode, We are getting sclk as 3.07 Mhz. Is it fixed clock generated by ADV7611; so even if data is less it will be filled by zero. Or it must be only...
View ArticleADuCM360 ADC Question
Hello everyone,Im using the Eval-ADuCM360 board and have some questions about the ADC.1. Is there any possibility to adjust the sample rate to any random number? (f.e. to use an timer to trigger...
View ArticleClik here to view.
What AD-ADC-FMC Adapter Board (Rev A or Rev B) do I need to connect...
Dear colleagues,I can not figure out which model adapter board should I use to connect connect AD9467-200EBZ to ML605.AD9467 Evaluation Board, ADC-FMC Interposer & Xilinx Reference Design [Analog...
View ArticleClik here to view.
What does the frequency stand for if you choose 2 in_voltages and capture a...
Dear all, I tried to use IIO Oscillascope to observe FM band spectra. When I choose 2 in_Voltages, the spectra shows an extra part of itself. The spectra is as follows:Whereas it is shown in the...
View ArticleADIS16227 Sleep Mode Initiation
Dear all, I'm new in the forum. I'm working in the University of Sheffield. In one of the projects we are working on, it involves using the sensor ADIS16227. We have encountered some issues when trying...
View ArticleADIS16209 How long until temperature reading is valid ?
I'm using the ADIS16209 sensor in a battery powered device which switches the sensor on every 10 minutes, reads MSC_CTRL and STATUS register until they are both zero, then reads TEMP_OUT, XINCL and...
View ArticleWould like to stream file output from the EVAL-ADISZ
I have just purchased the ADIS16364 along with the EVAL-ADISZ to get access to the output of the gyros and accelerometers. I have very little experience with SPI-compatible devices, and programing...
View Article[ADV7282-M] 0x04 "Extended output control" register.
Hello.I have some questions about 0x04 "Extended output control" register of ADV7282-M.We are referring ":I2P AUTODETECT CVBS Differential In Ain3,4, 480p/576p MIPI Out:" on the script file.(We are...
View ArticleADV212 with 576p @ 25Hz
Hello, We're trying to use the ADV212 in encode mode using VDATA[11:4] and JDATA bus. Our PLD is de-interlacing BT.656 video and passing frames of video (576p, YUV 4:2:2, 8-bits per sample) with...
View Article