AD8232 Filter Question
Hello Everyone,I'm sorry if this question is repetitive, but I tried to find similar questions on the whole forum and couldn't find anything, so I decided to start a new thread. I was looking up the...
View ArticleAD9978A: Enabling LVDS Test Pattern
Hello, In one of our projects we are using AD9978A AFE chip. We are not able to get the LVDS test Pattern with following commands 0x50 : 0x0010x41 : 0x1420x4E : 0x2000x40: 0x0000x42 : 0x0080x53:...
View ArticleAD9978 lvds pattern
Hi Analog Team. What should i drive on hd,vd signals if I am working on SHA mode.Is there any dependence to get lvds pattern with vd,hd signals.
View ArticleNeed Help: Data acquisition by ADIS16135 MEMS gyroscope
Hi, I need help regarding Analog Devices MEMS Gyroscope ADIS16135 and ADISUSBZ evaluation board (http://www.analog.com/en/evaluation/adisusb/eb.html) I am trying to calculate the noise and sensitivity...
View ArticleNational Instruments ADI free software
The ADI web site states that: "A free, downloadable version of National Instrumentations Multisim 11 Circuit Simulation Software, tailored for evaluating ADI components." I downloaded the software and...
View ArticleADxxxxSQ/883B with different dies?
Is it possible for parts to have different dies and bonding wires within the same date code/week code? We are looking at x-rays of two parts from within the same date code, yet the dies and bonding...
View ArticleAD-FMCJESDADC1-EBZ Board and ML605
I am using an AD-FMCJESDADC1-EBZ Development board connected to a Xilinx ML605 Development board. I'm using (http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms1-ebz/reference_hdl) as a guide...
View ArticleLinux based on Vivado?
Hey guys,Is there a plan to create a Linux project, based on Vivado with the new IP's and new Linux driver (Zedboard)?If so then it would be awesome if I can help/join you because its part of my...
View ArticleADV7343 - PAL60 CVBS output
Can someone help me set up the ADV7343 to output PAL60 on DAC1? The input mode is 24 bit RGB. The datasheet specifies it as a supported output but I can't find which registers to set up. Thanks
View ArticleAbout overcurrent protection and selecting external diode
Hi ,I have some questions about LDO products. #1,It looks like that ADI LDO products have current limitting protection, not current foldback.I just wondered why most LDO's current protection is current...
View ArticleAbout ADV7341
A value of RSET and RL is prescribed with the data sheet of ADV7341 as follows . For low-drive operation, RSET1 must have a value of 4.12 kΩ, and RL must have a value of 300 Ω. For full-drive...
View ArticleADV7341 720P OUTPUT
hi,adi, adv7341.pdf page34 said that is support 720p@30,720p@25 and 720p@24,and i had set the register 0x30,but no output from adv7341.why? where was wrong that i set? 20-Bit 720p@30/29.97Hz YCrCb In...
View ArticleAD5930 and Saw Sweep
Hi, I'm doing some application with AD5930. I'm trying to do a frequency sweep from 115kHz to 125 kHz in a saw-sweep mode. Frequency must rise from 115k to 125k and then again from 115 to 125k...
View ArticleAD-FMCOMMS3-EBZ "RF engineer’s platform"
Can you explain what you mean by the text highlighted in yellow below (from the 2nd paragraph of the AD-FMCOMMS3-EBZ wiki users’ guide)?...
View Articlehow to regenerate IP cores from core generator and rebuild the...
We want to use AD-FMCOMMS 2EBZ on ML605 Evaluation board. I downloaded the project(Zip file) from this below link.http://wiki.analog.com/resources/eval/user-guides/ad-fmcomms2-ebz/reference_hdl. Can u...
View ArticleAD-FMComms2 HDL support for Altera FPGAs
Hello, I am interested in interfacing the AD9361 evaluation module (AD-FMComms2-EBZ) with an Altera development board (Arria-V). I notice there is a significant HDL base for interfacing the AD9361...
View ArticleVivado for FMComms2/3/4
Someone by email was asking me: Where is the Vivado project for the AD9361 project? If it's not available today, when can I get it? (and where will it appear?) Thanks
View ArticleDemultiplexing Excitation from AD7746
For my application, I would like to demultiplex the excitation from AD7746 in order to sequentially direct it to different leads. I am not familiar with issues for maintaining signal fidelity when...
View ArticleVery high frequency Precision Rectifier
Hello, I have the application where i have to rectify high frequency single ended ac signal to dc. I want to make High frequency Precision Rectifier whose input signal frequency is 250KHz with ±10V...
View ArticleADA4096-2 & the Filter Wizard
Hi, After using the filter wizard for a design, I am finding some ambiguity in the results of the software, vs data sheet specifications. Or probably a misunderstanding on the results on my part. The...
View Article