HDCP/EDID Controller Error Codes of ADV7511W.
Hello. I have a question about HDCP/EDID Controller Error Codes of ADV7511W.The DDC Controller Error register (0xC8 [7:4]) indicates 0xF at low temperature operation.I see...
View ArticleIf ADN4612 can both support 1.25G 2.5G and 10G ？
My boards use SFP and SFP + interfaces, wanted to support both 1G 2G 10G rate, if this can be support? what required for pcb layout,if have schematic for reference。when the rate is 2.5G it need...
View ArticleHow to check if the packet or AVI checksum error with ADV7630 for secondary path
In general condition HDMI RX can't checked out if HDCP error, So full screen snow points video appears.ADV7630 have two signal path. I think if RX HDCP error, there should be some checksum error...
View ArticleSD Data Logger mode with spikes(EVAL-ADXL362Z-DB)
Hello all,I'd like to ask you about EVAL-ADXL362Z-DB with SD Data logger mode.I tried DB with following conditions. Battery : coin batteryMode : SD Data logger modeODR : 400 or 200 or 100Range : 2gLow...
View Article8Khz Sample Rate BF52xC1 & G711u-law
Hi there, So i've implemented what is essentially a "Multicast Speaker" on the EZ-KIT BF527. It samples G711u-law packets, delivers the payload to the G711 decoder (the demo version from ADI) and the...
View ArticleBoth PLL AD9523-1 not lock. Board FMCOMMS1.
I have the boards Avnet ZedBoard and AD FMCOMMS1. From FPGA I give 100Mhz CLK signal to the AD9548, which generate 122.88Mhz clock to the AD9523-1. I need 98.304Mhz CLK signal for ADC from AD9523-1....
View ArticleLinker error
Pulled the code down from SVN, compiled it and when it went to go link, I get this:[Error li1021] The following symbols referenced in processor 'p0' could not be resolved:...
View ArticleADAU1701 Selfboot Problem
Hi Everyone, I need your help please! I am busy with a design using the ADAU1701. I have bought the evaluation kit and as a test program just output a 500Hz tone to all 4 DACs. The program works...
View ArticleADV7393 cable detect
Hello all, Please let me know about the CABLE DETECTION Subaddress 0x10, Bits[1:0] described in ADV7393 datasheet P.66.We connect cable as attachment but, Cable Detection register 0x10 remains 0 in the...
View ArticleError occuring while programming ldr file into internal flash
Hello, I'm using ADSP-BF518 and ICE-100B emulator. While i am trying to load .ldr file into internal spi flash through flash programmer using the program which is located at "C:\Program Files...
View ArticleSigmaDSP evm in combination with amp evm
Hello, Is there anyone with good knowledge of ADI EVM:s that could fulfill these demands: 1)6 analog inputs, SigmaStudio DSP, 1 analog output (for sub) + 6 outputs that... connect to 6 Channel amp...
View ArticleRGB settings in ADV7511 Reference design
Hi all, I am working on ADV7511 Xilinx Evaluation Boards Reference Designfor Zedboard. I am able to display it on monitor but the display colors don’t appear to be normal(dull orangish), when...
View ArticleUndefined References in Zed cf_hdmi demo
I downloaded the ADI7511 API from github, and I'm trying to build the demo software but I get lots of undefined references: undefined reference to `HAL_GetMBSwitchState'undefined reference to...
View ArticleSlew rate VS input level (ad8641?)
Hi, I'm pretty new to analog electronic. I've been learning from appnotes and datasheets, and i've sometime seen reference of slew rate VS input level.I've understood the effect of slew rate in audio,...
View ArticleADF4351 Phase Noise
Hello, I am using ADF4351 for WLAN design and my LO phase noise requirement is -95dBc at 100KHz. My REF is 30.72 MHz crystal (Si8208) and has very good phase noise performance. Using adsimpll, the loop...
View ArticleSelf Latching Comparator
Hello, I'm trying to use the ADCMP553 comparator to capture and hold a fast trigger signal. I would like to somehow feedback the output of the comparator to the latch so that when the comparator goes...
View ArticleADuM540x Silicon Errata
Hello, I have recently encountered a problem with some of our products based on the ADuM5401. It turned out that there was a sprinkling (9) of old stock of these parts (date code #0830) while most are...
View ArticleVisualDSP++ Floating License Server/Client Requirements
Hi, I would like to order VDSP floating license per 5 machines. I have following questions.1. Could you provide system requirements for server and clients? I plan to install server to Windows Server...
View ArticleADV7513 OUTPUT VGA SIZE
Hello all, Can ADV7513 be operated when the input to this is VGA (640*480 at 60HZ) ?When this system is connected to monitor (LCD), displayed image looks like dark.If you have known issue likes...
View ArticleLinux driver for ADV7441A
Hi,I got my customized board with ADV7441 on it , now i am in board bringup stage, Pl. let me know from where i can get linux driver for ADV7441A part. Thanks,Sachin Nalbalwar
View Article