ADV7513 HDCP
Hi , Can we disable the HDCP and use ADV7513 . from the register setting find that it is possible . Do you have plans to roll out a Non HDCP version of ADV7513 Thanking you With best regards and wishes
View ArticleADV7513 Image not stable
Hi, I'm using a FPGA borad that uses an ADV7513 as a transmitter totransfer an image to HDMI. Currently, I'm testing an input formatCEA-861 format 20 image. The setting I did is as the followings....
View ArticleADAU 1442 PCM Inputs
Hi I have been using the ADAU 1442 as an audio router for 4 I2S inputs. Is it possible to get the ADAU 1442 to take PCM inputs instead? Thanks, Garry
View ArticleADE7753 work as a Bidirection or Unidirection metering
Dear Sir, We will like to design energy meter for Home Application and Smart Grid for Bi-direction Metering. Please let us know ADE7753 work as Bi direction or Uni direction metering in single phase....
View ArticleNeutral Signal Connection in ADE 7758 IC
Hello, Please Tell, Weather i can connect Neutral Signal to PIN no 13 of ADE 7758 as per connections Mentioned in Test Circuit in Data Sheet.If not then please tell me right way of connecting it.
View Article3Phase 3 Wire Vrms measurement ?
Conditions : 3Phase ( R, S, T )3Wire (Delta Connection) question 1. measurement Vrms : Vrms(R between Earth), Vrms(S between Earth), Vrms(T between Earth) question 2. measurement Vrms : Vrms(R between...
View ArticleADE7878 Angle Selection - Instantaneous Angle Register Update?
The ANGLESEL bits of COMPMODE allow you to change between three modes for measuring angles via the results provided in the ANGLE0, ANGLE1, and ANGLE2 registers. The modes are voltage-current,...
View ArticleBlackfin KOOP not alive anymore?
Hello:I cannot access http://blackfin.uclinux.org/gf/. This website does not seem to be alive. There were some good threads there, files, documentation, etc. It would be a loss if that website was...
View ArticleAD650 F/V converter not working.
Hi,we are using AD650 as frequency to voltage converter. After going through all the related application notes and datasheet, i have designed the circuit. And now we are in doing bringup for the same....
View ArticleAD9467 native FMC: VHDL version instead of Verilog
I've downloaded the included .bit file to check that the AD9467 FMC card is working on the Xilinx Kintex development board (KC705). I was hoping to develop some VHDL based algorithms to test the board...
View ArticleADV7511 Reference Design for KC705 Development Board
Dear Members and the Employees of Analog Devices; I am trying to use ADV7511 reference design on KC705 using ISE 14.6. However the design stops working if I regenerate the netlist & bitstream for...
View ArticleAddressing 4MB flash memory from BF53x
The BF53x allows 4 contiguous banks of 1MB asynchronous memory (512 x 16-bit words) to be accessed using 19 address lines A[19:1]. There are 4 AMS[3:0] lines to act as a chip select (one-hot inverse...
View ArticleOdd SPI response from ADIS16488
I'm connecting to an ADIS16488, and debugging the SPI protocol. I'm re-transmitting PROD_ID as recommended, but getting a strange response. I attached the scope outputs. The MOSI looks fine, and the...
View ArticleHuge offset voltage with ADA4897-1
I have a standard inverting amplifier stage with Rf = 100k and Rg = 10k (A = -10 V/V). The amp is powered from +/-5V and the positive input terminal is connected to 0V. Pins 1 and 5 are open. Pin 8...
View ArticleADIS16265 Calibration
I've been having a number of problems attempting calibration of the ADIS16265 with regards to the RevD datasheet. First, I have been unable to located an application note that describes the correct...
View ArticleADIS16480 - How to restore complete factory configuration?
We develop a platform stabilisation application with ADIS16480. First, ADIS16480 was connected to an ATXMega192A3U controller and all worked fine: We could change registers, read Euler angles etc. A...
View ArticleRunning the Buildroot image for custom BF537
I am trying to make a blackfin buildroot image to run after u-boot on my custom BF537 board. I have downloaded the latest buildroot from sourceforge: blackfin-buildroot-2012R2-RC5.tar.bz2 and have had...
View ArticleADV7623 EDID information coming from sink device
Hello, Does ADV7623 pass EDID information coming from monitor(sink device) to DisplayLink(source dvice) as it is or delete the unnecessary information, in the case the EDID includes information of...
View Articlethe question about ADN4612
hi dave because the 10G(XFP) optical module with the CDR circuit,the 1.25G,2.5G optical module without,so i want to add the CDR on the PCB,but i must remove the CDR when i insert the 10G optical...
View Article