VisualDSP++ 5.0 Update 10 installation
I need to install the version 5.0 update 10 ("VisualDSP++ 5.0_Update10.vdu") in my system. It doesn't let me go down from version 5.1.1 which is already installed.
View ArticleBuffer(voltage follower) op-amp recommendation
I have AD8222 amplifier eval board. I want to place Buffer(voltage follower) op-amp in front on AD8222. Application is pH measurement I like recommendation on differential input Buffer(voltage...
View ArticleADF4351 PLL programming question
Hi, This is regarding this PLL I am using for a university project. This PLL is part of a commercial transceiver and I am using Altera Cyclone2 fpga development board for programming. Currently I am...
View ArticleADV7623 CEC connection
Hello, I am designing the ADV7623 HDMI tranceiver into a product and understand all of it's operation except for the CEC connection. As I understand it, the CEC connects from a source device (Blu ray...
View ArticleClik here to view.
adv7842
Any tips on how to optimize tv capture to reduce fake colors during motion and jagged edges on still wires that have curves in them?
View ArticleADV7186 full data sheet
I'm trying to locate a full datasheet for the ADV7186. From the short version on the website it looks like this IC will fit my need. I need to convert NTSC to 24 bit RGB to drive a TFT LCD. I've...
View ArticlePVP - THC0 Coefficient updated on-the-fly But not took effect.
Hi, I am using CameraPipe PVP as below, EPPI0 --> IPF0 --> THC0-->OPF0--DMA46Its working properly But if I update THC_MINTH or MAXTH register in running time, the change not affect the...
View ArticleQuestions about AD9279 Reference Design
The design: AD9279 Evaluation Board, ADC-FMC Interposer & Xilinx ML605 Reference Design [Analog Devices Wiki] I am reading the data from Microblaze but not sure how it is arranged for all 8...
View ArticleACP and ISRC support in SPDIF format
Hello,I am using ADV7619 as HDMI Receiver. Output audio from ADV7619 is in SPDIF format. I would like to know whether this configuration will support ACP and ISRC feature or not?Do i need any specific...
View ArticleSPI slave select in Software control
Hi All, I am using the ADSP-BF538F processor. I am configuring the SPI2 in master mode in CCES 1.1.0 IDE.I want to use the SPI2 slave select SPI2SEL1 in user software control and the configuration is...
View Articlecontinuos conversion mode in ad7195
Hi,I can notread thead7195incontinuosmode.As describedon page 30of the data sheet, when the lineDOUT/RDYgoes low, I write the data0x58 on theDINline (seefig.1), andafterI readthe datapresent on the...
View ArticleLimitations of using AD8352 amplifier with AD9434 ADC?
Hi Everyone, Are there any limitations of using the AD8352 amplifier with the AD9434 ADC? They are shown together in the ADC datasheet, but now the website for that part recommends a newer amplifier,...
View ArticleADUM3200 Working Voltage Specs?
I have a customer that is looking for a digital isolater, 2 channel, 1 input and 1 output. - Powered from 5V and 3.3V - The working voltage must be at least 1200VDC. - It must support a UL creep-age...
View ArticleDose ADI have detailed document for ADradioNet?
Hi, I went through the source code , but still found that it's hard to get a clear picture for this protocol. Confused by some words like "CoOrdState_A" , "CO" , "MODE_A" , etc. Do you have any...
View ArticleClik here to view.
ADXL343 standby mode
Hi,I want to use the ADXL343 accelerometer in a design that needs very low power and I am wondering if the interrupts can work in standby mode? In the datasheet, I can read that no measurements are...
View ArticleClik here to view.
Question about the ADV7180 with the output picture shake
Dears I use the ADV7180 to do a design , met a question with the output image was wobbly if the input signal is 480I, but input signal 576I is OK! The s-video、cvbs、Ypbpr interface all occur...
View Articlebuilding drivers for adsp-bf537 ez-kit lite in simulink
Hi,I'm using MATLAB/Simulink to build models for adsp-bf537 ez-kit lite but not all drivers' blocks are available in "analog devices blackfin/adsp bf537 ez-kit lite" library. so how could i build a...
View ArticleProgramming AD5122A
Hello, Need help for programming Digital potentiometer AD5122A in I2C mode. The documentation of Analog Devices on steps and sequence of programming for reading the RDAC or Control registers is not...
View ArticleADF4351 Vref
Hi, Could someone help me to understand how the Vref is generated and used within ADF4351? In one of our board, Vref for ADF4351 is showing 350mV. For that component the lock detect is not going high...
View ArticleSigma Studio Ver 3.11 Build 1. Rev 1356 Mixer Bug?
I'm running Sigma Studio Ver 3.11 BUild 1. Rev 1356. And I have a 4 input, 3 output mixer. My assumption from reading the literature is that the inputs are represented by the rows of controls,...
View Article