Problems with ADIS16265 EVAL Board ...
Hi everybody, I am just working on the implementation of a ADIS16265 Gyro into my roboter application and a have problems with the readings of the Evaluation board. The Board is sending sometimes...
View ArticleHow to calculate Power & Power Factor using Energy registers in ADE7753
How to calculate Power using Energy registers & Line Accumulation Cycle mode in ADE7753. Can Power factor (PF) can be as ratio of Active Energy & Apparent Energy?... as it is ratio of Active...
View ArticleAmplitude level Problem
hi.. i am HariPrakash .. I am working with DDS function generator using AD9834 dds ic. i need up to 3.3MHz frequency sine, triangular output... In low frequency like 1KHz to 300KHz my dds ic...
View ArticleSPI connection on MikroElektronika STM32 to ADIS16210
Hi, I just need to get my read/write operation working correctly. I'm building with MikroC on an Easy MX Pro v7 STM32 for ARM board. The setup parameters I've used are: 16 bit, clock idles high, data...
View ArticleFlash Programming with VDSP without license
Hello, I need to download firmware in various DSP in Blackfin Family (BF518F, BF506F...) to program our boards.We already use 3 licenses in R&D office: is possible to run another VDSP environment...
View ArticleADXL325 vibration bias
I am currently using the ADXL325 sensor to measure the acceleration normal to the ground of a moving vehicle (using Y-axis, facing downward) and have noticed a bias which occurs when the vehicle...
View ArticleICE-100B issue
Hi, I have been using ICE-100B to debug our custom designed Blackfin BF537 DSP board. I has worked without no problem even by this afternoon. Suddenly it wnet out and i m no longer seeing MON led...
View ArticleADA4411-3 VIDEO FILTER doesn’t work properly
I am using a electronic circuit that the input to it is an NTSC CAMERA. The input video isClean without any noise. I have noticed that the output video signal from the circuit I am Using has a noise...
View ArticleExternal RAM and Flash suggestions
Hello, We are using ADuc7126 for a project that now requires external RAM and flash due to new requirements. Currently, most of the address lines are currently being used for I/Os as well as AE, /RS,...
View ArticleAD9958 programming
Hi,I am currently trying to program the AD9958 Chip via a AT91SAM3U4E mikrocontroller from Atmel, but it is not working.The Chip select signal is set low and the SCLK is running but when i download my...
View ArticleSample rate killer
I am putting a mux in front of ADuCM361, so I have to change gain in ADC ISR when I switch channels I start with your Meter example and set the sample rate to 2000 S/s. At this point, the gain is not...
View ArticleBug Report: Gain/Reading error
The following doe NOT happen at gain of 1: When using a high gain to study a sine wave input, the gain can amplify the signal beyond the +/-Vref. If the gain is set ONLY ONCE before the scan starts,...
View ArticleLabView Driver for AD5370 Eval Board?
Hello, is there a LabView Driver available, or a way to control through LabView, the Eval board for the AD5370 40 channel DAC? If not with LabView, is there another way (other than the Analog Devices...
View ArticleADV7513 power at 3.3V
The data sheet for the ADV7513 list the total power at 3.3V as 1mW. While this is a low power part, that seems to be too low, especially since it is 256mW at 1.8V.
View ArticleADuCM360 + AN-1160 + CM3WSD + downloading sample.hex file
The utility application CM3WSD includes a "sample.hex" file. That file is fairly straight-forward until one gets to: :04000005000001E90D The Intel hex record format defines a record type of 05 as:...
View ArticleAbout AD9945(A/D Converter)
Hello ! I have puestion abou AD9945.I want to know , The maximum and the minimum of Internal Clock Delay (tID) at clock rate is 35MHz.These do not sppear in a data sheet. Best regards.
View ArticleADv 7611 Register settings
when i write 0x40 to register 0x33 ie to enable the DLL output on LLC output .. ADV 7611 is not generating any timing signals...but when i disable itiic_write_7611(0x98, 0x33, 0x00) its working fine ?
View ArticleDDR2 operations using ODT
Per the datasheet, EE-349, and http://ez.analog.com/message/64553#64553, the '21469 ODT output is static and once set stays on. This behavior is not compliant with the JEDEC DDR2 standard. Instead it...
View ArticleADV7180 - How to starts coding
Hi. Very first time i am using video decoder ADV7180 (48 pin LQFP) in our product. to decode to CVBS output from camera into the ITU565 output.please tell me how i program the ADV7180 from our micro...
View ArticleHow to calculate to convert Full/Limited range(ADV7611)
Hello. I have a question about calculating formula to convert full/limited range. According to "Figure 38. CP Data Path Channel A (Y) for HDMI Mode" of UG-180 Rev.B Page.112, it seems that the formula...
View Article