About ADP2164
Hi, I have some questions about ADP2164.In my system, it requres to use different power rails for VPIN and PVIN like the attached file.These two inputvoltage are not applied to ADP2164 at the same...
View ArticleClik here to view.
How to route TDM audio through multiple ADAU1701s?
Hello all, We're developing an audio mixer around a ring of ADAU1701s where each receives a TDM steam from its neighbor, adds in two analog inputs and sends the mix through to the next -1701....
View ArticleHow to connect a 21369 EZ-KIT to ADZS-USBI2EZB and EVAL-ADUSB2EBZ
I can't seem to find any information on how to connect a 21369 EZ-KIT to a ADZS-USBI2EZB adapter and subsequently to a EVAL-ADUSB2EBZ interface. Any help appreciated.Daniel
View ArticleSome questions of ADV7619, again
Dear Sir/Madam, maybe DaveD,I have some questions for your device ADV7619.Please refer to my enclosed file.The chart shows our new design and are going to use ADV7619. Q1.ADV7619 provides two HDMI 1.4...
View ArticleAD-FMCOMMS1-EBZ relayout issue:PIC firmware programming to a micro-controller...
Dear EngineerZone:I want to re-layout the ADI-fmcomms1-ebz board.how to a PIC firmware download to micro-controller(PIC18F24J50-I/ML) on board.i use ML605 and no-OS driver.Thanks.
View ArticleAD5930 and AD5932 evaluation board software commands
Hi, This discussion explains how to use the new dll library available for both Windows 32 and 64 bits OS. We aim to provide a detailed explanation of the dll functions and the commands associate with...
View ArticleAdditional Parametric Information for ADV7511W and ADV7611
Hello,We need to obtain some additional parametric information which is to be incorporated into our component library. Parts entered into the library are not approved by the component management...
View ArticleAD9467FMC connectivity with Zedboard
Hello all, I want to interface AD9467FMC with Zedboard and Waveform Generator but i have some problems and confusions that what should i set on Zedboard jumper either 1.8V or 2.5V.Secondly i want to...
View ArticleAD9361 SFDR
I measured AD-FMCOMMS2-EBZ TX single tone performance@2GHz. At maximum output, atten=0, scale =0.5. The SFDR is about -60dBc, and also find spur at CF+/-88K(-55dBc) and CF+/-320KHz(-65dBc). Is this...
View ArticlePink Noise Generator
I've been making use of the white noise generator with the pinking filter after it. For my first application it works perfectly, but I have another application where the requirements are a bit more...
View ArticleJitter Simulation of a Simple inverter in Cadence?
I have actually dumbed down the question for a better understanding. The thing is if I run a 'pnoise' simulation for 'jitter' analysis of an inverter with a 100 MHz clock (with 50% duty cycle) at its...
View ArticleAD-FMCOMMS1-EBZ REF DESIGN- MODIFY+REBUILD
EngieerZone: What is the best way to make modifications to AD-FMCOMMS1-EBZ/ML605 reference design and rebuild. I'm familiar with ISE design flow not EDK. 1) Can you modify individual source files like...
View ArticleProblem with the BF592 frequency settings
Hello everybody, for my current project I am using the BF592. I've got problems while changing the frequencies to their maximum values on my own hardware.First I use the function from the EZ-KIT called...
View ArticleH.264 codec in blackfin??
1) Is it possible implement both H.264 encoder and decoder in the same blackfin. 2) I have ADSP-BF527 EZ-KIT Lite, would I be able to compress live BT.656 format video input, so that the output rate...
View ArticleADAU1701 have level data feedback to MCU?
Hello, friends, Nowadays, I use ADAU1701 to design a soundbox. I use a MCU to control the ADAU1701. Is there any method to get the input signal ' level, or ouput signal ' level from...
View ArticleAD9361_Initialization
i am using AD9361 device in my circuit. I want to know after power on the AD9361 chip, what i need to do to operate the AD9361 chip.like i want see clock output from AD9361 chip and i want to operate...
View ArticleMaking video system running Linux with ADV7511 on ZedBoard
Hello everyone!I'm trying to develop the subj using reference design from here: http//wiki.analog.com/resources/fpga/xilinx/kc705/adv7511But I need a system with two images overlaying one another with...
View ArticleAD-FMComms2 HDL support for Altera FPGAs
Hello, I am interested in interfacing the AD9361 evaluation module (AD-FMComms2-EBZ) with an Altera development board (Arria-V). I notice there is a significant HDL base for interfacing the AD9361...
View Articlead9552 dc bias input changes to higher value
Hi,I am using AD9552, reference input applied a 40MHz clock signal.I am using AC coupling, I applied 1V dc bias with resistor divider from 3.3V power supply.A0-A2 are connected high. Y0-Y5 are open....
View Article