Sine wave in No-os driver FMcomms1-ebz
Hi, I ask you how sine wave is generated in No-OS driver-C-program or by any other way? Can I stop running this sine wave generation? if yes then how? It is highly required in our project to stop its...
View ArticleClik here to view.
bf609 running frame capture example
Hi,I was trying to run the frame capture example for bf609 ez kit and video decoder EI3. I get the following messages in the console. UYVY422 video, Capture frame to fileDecoder Soft Config -...
View ArticleADV7403 power supply
Hello all Please let me know voltage value about below pin for decision of voltage proof in capacitorCAPY1（61）CAPY2（62）CAPC1（68）CAPC2（69）CML（65）REFOUT（64）BIAS（67 daisu
View ArticleADV7403 power sequencing
Does the ADV7403 need special power-up/down sequence for 3.3V and 1.8V?
View ArticleEmulator ICE-100B error
Hi,I am using a customized board based on the BF-538F. I am trying to emulate the using the ICE-100B emulator but I am getting the following errorError: 0x80048015Error Description: Open Device Driver...
View ArticleClik here to view.
ADV 7403 Video Decoder Power Consumption
Hi, I am using ADV 7403 Video Decoder in my design to convert the YC(luma and chroma) Analog Input signal to Digital signal in BT .656 standard. I have powered-on my system. I have found few...
View ArticleCustom design in Zed board, FMCOMMS-EBZ, Reference design
Hi, I have downloaded vivado 2014.2 and build all the libraries and then project for ZED board and zc706 board.Now my query is how to proceed to add a custom design into my project.Any flow is there?...
View ArticleIIR filter crashes on the fly
Hi, My set-up consists of three POTs (Q,F,Boost) connected to the ADC of a uC. The analog values are converted to an index that corresponds to Frequency, Q, or Boost level that are used to calculate...
View ArticleADV7619 pink lines after switching from unsupported to supported resolution
Hello, I have run across an issue where I get what appears to be, two vertical pink lines in my output. Both lines appear on the left side of the image, as shown in the attached screen capture. What...
View ArticleREFERENCE DESIGN FORMAT
Hi,I download some reference design from Analog reference design the schematic has .sch and PCB .pcb that I think it is P-CAD formats. I try to import these files to Altium designer as P-CAD and others...
View ArticleClik here to view.
Looking for a proper OPA for driving a symmetrical cable
Hi there, I am desperately looking for a proper OPA that can drive about 3 meters of symmetrical, shielded (XLR) cable. My audiocodec outputs a differential signal with a 2.5V offset. This way both...
View ArticleEVAL-ADAU1442 GPIO with 96kHz
I am having trouble with the read / write registers for a volume control using the EVAL-ADAU1442EBZ board and GPIO expansion - everytime I turn off the device, the volume is reset to 0dBFS - the...
View ArticleUsing ADT7470 as Tacho Only
I wonder if it is possible to use the ADT7470 only as a 4 inputs tachometer, not using the PWM outputs and not using the temperature sensors?If so what is connection requirements of the unused...
View ArticleBlimp feature needed
The following features should be considered in a new version Blimp.1> Unicode support1) When adding Unicode language words into Blimp, there is no “All select”. If OSD has hundreds or...
View ArticleADV7511 snow noise
Hello ADI ! I use the adv7511 as a hdmi transmitter.I got a snow noise in some sinks when hot plug hdmi cable.I guess it's a problem of hdcp,because when I turn off the hdcp,this problem will not...
View ArticleAD7190/AD7191, questions for input and PGA inside
Hi, We are now studying AD7190 and AD7191 to be receiving differential voltage output from magnetoresistive current sensor.So far, AD8421 instrumentation amp is used for the purpose, but considering...
View ArticleStreaming with AD9361
Hi all, Can someon tell me how to use the streaming in AD9361!? Is it linux based or it can be used even with non os-reference signal. How can I stream a .wav file through fmcomms2 from one zedboard...
View ArticleSD card image file
I got SD card with fmcomms board which has already image file for Ubuntu and I have used also that os with HDMI monitor but I done some updates in the os and now zed board is not reading any os from SD...
View ArticleAD9361 - Sample rate does not generate expected output
Hi, I am running the AD9361 FMCOMMS2 Board on a ZC702 Xilinx Board with the latest GitHub no-OS SW drivers and latest GitHub HDL code for Vivado. The AD9361 is configured to run in 2tx2rx mode and I...
View ArticleAD9467-FMC with Zedboard and Vivado
Hello, Does the reference design work with Vivado 2013.4? This is thedesign suite that was packaged with the Zedboard. I receive thefollowing error when running the download.bat script. (See image)...
View Article