ADA2200 Question
Dear Sir/Madam, I use ADA2200 fortestinginaproject, and need to measurethesensorinputsignal'samplitudeandphase. 1. Because input singla could notguaranteeconstantwithin a shorttime,Iwant touse2ADA2200...
View ArticleADE7953 evaluation board software
Hi,We have bought one ADE7953 evaluation board, but we are unable to connect it to the computer using the sooftware you provided. We have follow the next steps: -Connect the board to the computer (We...
View ArticleRofs pin of AD5556
Can the Rofs pin of the AD5556 be left unconnected when used in unipolar two-quadrant mode? It appears that this would increase the feedback resistance from 5kΩ to 10kΩ. Would this then also increase...
View ArticleADE7878/7880 How to choose filter inductor for Neutral connecting point
Hi,We are using ADE7878 & 7880 for three phase static energy meter.Three phase voltage and neutral input connected to three phase Isolation SMPS and parallel take the wires to ADE input channels...
View ArticleAD7357 serial interface
Hi guys,I'm currently using the AD7357 and I was wondering if I can pull up NCS (N for not) right after the 16th falling edge of SCKL or if I should wait the 16th rising edge of SCKL as shown on the...
View ArticleAD9684 Byte Mode Problem
Greetings! We are currently trying to configure and debug AD9684 in byte mode. For now we are using 2 DDC (DDC0 and DDC1) which are configured as follows:Register address datax300...
View ArticlePower up procedure for ADE7878A
Hello I'm currently using AD7878A with atmel microcontroller. communication between the two is through SPI (isolated using isolators) and power domain of ADE7878A and Microcontroller is different. In...
View ArticleHelp connecting SDP-B in SDP Panel and LabView
Hi there, I am trying to connect the SDP-B in SDP panel but without success. I am intending to connect the ADAR7251 to EVAL-MMIC-2 through SDP-B to provide live data in MATLAB. I have tried using...
View Articledriving the AD9364/65 with switching supplies?
Would the performance of the AD9364 or AD9365 be degraded if the 1.8V supply on the 64/65 were driven directly by a switcher such as the ADP5034? Do you recommend using an LDO for this application?...
View Articlemax supply current on AD9364,65
Customer is asking for max supply currents on AD9364, typs are given in the datasheet. Are there any distributions of supply current, from characterization, that can be given out? I think on this CMOS...
View ArticleEnergy Meter IC to measure single phase parameters in a 3P3W system
Hi team, Energy Monitoring and Metering I am planning to use ADE 7753 single phase energy meter in my design. The application would be to measure the voltage between the two phases between ƟA and ƟB...
View ArticleClik here to view.
ADRF6806 Eval Kit Non-Responsive
I recently obtained a ADRF6806 EVAL BOARD Z kit from DigiKey, and have been struggling to make it do anything. Disappointed at the lack of instructions, but poking around seems to result in finding...
View ArticleADV212 - using 5/3 wavelet kernel and RCVAL
Hi,I have a few questions regarding the use of the 5/3 wavelet kernel and the RCVAL parameter with the ADV212. * The ADV212 supports the 5/3 wavelet kernel which is mathematically lossless. Does this...
View ArticleWhen will the ADALM-PLUTO be back in stock?
When will the ADALM-PLUTO be back in stock?
View ArticleADF4355, ADF4355-2, ADF4355-3, ADF4356, ADF5355, and ADF5356 evaluation board...
Installation process:Disconnect any evaluation board.Download and run the attached installer.Click Next/Continue/Finish when asked.Connect your evaluation board.Windows will detect the evaluation board...
View ArticleADF5355 fast lock times
On page 35 of the ADF5355 datasheet there is a mention that "Much faster lock times than those detailed in this data sheet are possible; contact Analog Devices for more information". My application...
View ArticleUsing Arduino to program/control ADF4356
Hello, I am working on project and I am stuck with controller for the synthesizer. I was wondering if any one has a sample program to control ADF4356 using arduino. your help is highly appreciated. tnx
View ArticleADE7753 ZX interrupt problem
Hi everyone, I am building an energy meter based on the ADE7753. I have been trying to calculate the Vrms ,Irms and the energy over a specific period. I am trying to use the zero crossings (ZX)...
View ArticleADXRS453 Angle Computation
Hi,i worked with ADIS16488 inertial sensor...about DELTA ANGLES parameter in datasheet: ±720° range, 0° = 0x0000, 1 LSB = 720°/2^15 = ~0.022°.now i am working on ADXRS453 gyro and i used same formula...
View ArticleHittite HMC-T2100 Software Support
Hi guys,We are currently using the HMC-T2100 function generator for our research and I need to do a continuous sweep, with increments within a certain period, within the bandwidth (10MHz-20GHz) for...
View Article
